ocr-030721171446.djvu: eKnigu

Home / lib / 0pre-Library / 2003-07_unsorted /

ocr-030721171446.djvu

Size 2.9Mb
Date Nov 30, 2003

Mode B is the mode used for calling CQ, or other operations where more
than one station is intended to receive the communication...
Since both stations are constantly switching from receive to transmit and back again,
fast switching times are required for AMTOR ARQ operation...
When he is ready to have you transmit data to him, he would enter the
changeover sequence, which consists of a FIGURES shi, +?...
If you want the Satellite bulletins and DX bulletins, you would type
NAVMSG ES and press return...
When in Convets or Command Mode entering a Ctrl-X will cancel all characters input
from the keyboard back to the last un-PASSed carriage return (unless PACTIME has
expired and CPACT!M is turned on)...
(See CMDTIME for returning to
Command Mode from Transparent Mode.) This character is also used for special
commands in non-packet mode...
The standard connect message, with stream ID if
appropriate, will be output to the terminal and the mode specified by CONMODE will
be entered on the UO stream if you are not connected to another station and NOMODE
is OFF...
Recent observations have proven that a better algorithm for avoiding collisions
between end-user stations, while still allowing digipeaters the high-priority access
they require is achieved using persistence and slottime to determine proper transmit
intervals, and setting DWAIT to 0...
When a selcal is specified, xxxx[xxx], the
TNC will call the specified station using SELFEC (Selective FEC)...
See also: proode
� INvert ON I OFF
default OFF KAM RTTY/ASCIUAMTOR
When ON, signals received in RTTY, AMTOR or ASCII are inverted...
The
MONITOR command must be ON for this command to work, and if connected
MCON must also be ON...
See also: gateway, hid
� MYNode xxxxxx-n v2.8
default MYCAI. All Units KA-NODE
This command tells the TNC what callsign is to be used when a remote station is
connecting to the KA-NODE...
This will also allow you to copy AMTEX messages (refer to the 8th
Computer Networking Con/'erence papers for details)...
When the selected character is entered during CW
transmission or within text to be used for CW transmission, it will cause the NEXT
TWO character codes to be combined...
If a connection stays in a remote device busy
state (continues to receive RNR frames) for RNRTIME, the TNC will disconnect...
The
first number (u) is used to increment a counter when a valid mark/space or space/mark
transition occurs in the received signal (i.e...
WhenON,
software flow control is enabled and the START and STOP characters are sent by the
computer to the TNC to control the flow of data...
When set for software flow control, all characters can be sent in Transparent Mode
(including the XON and XOFF characters) by setting TXLOW ON, XFLOW ON
and TRFLOW OFF...
B7 215 D7 247 F7
X 24' 18 CAN 56 38 8 88 58 X 120 78 x 152 98 184 B8 216 D8 248 F8
'Y 25 19 -M 57 39 9 89 59 Y 121 79 y 153 99 185 B9 217 D9 249 F9
Z 26 1A su 58 3A : 90 5A Z 123 7A z 154 9A 186 BA 218 DA:250 FA
[ 27 lB ESC 59 3B ; 91 5B [ 124 7B { 155 9B 187 BB 219 DB 251 FB
/ 28 1C Fs 60 3C < 92 5C \ 124 7C I 156 9C 188 BC 220 DC 252 FC
] 29 1D cs 61 3D = 93 5D ] 125 7D ] 157 9D189 BD 221 DD 253 FD
^ 30 1E 62 3E > 94 5E ^ 126 7E ~ 158 9E 190 BE 222 DE 254 FE:
_ 31 IF s 63 3F ? 95 5F _ 127 7F DL I59 9F 191 BF 223 DF 255 FF
Copyright 1989, 1990, Kanttonics, Inc...